- 您现在的位置：买卖IC网 > Sheet目录368 > W25Q32BVZPIG (Winbond Electronics)IC SPI FLASH 32MBIT 8WSON
W25Q32BV
7.2.23 Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “20h” followed a 24 -bit sector address (A23-A0) (see Figure 2). The
Sector Erase instruction sequence is shown in Figure 21.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase
instruction will commence for a time duration of t SE (See AC Characteristics). While the Sector Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of
the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Sector Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase
instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB,
BP2, BP1, and BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
0
1
2
3
4
5
6
7
8
9
29
30
31
Mode 3
CLK
Mode 0
Instruction (20h)
24-Bit Address
Mode 0
DI
(IO 0 )
23
*
22
2
1
0
DO
(IO 1 )
* = MSB
High Impedance
Figure 21. Sector Erase Instruction Sequence Diagram
Publication Release Date: October 04,2013
- 43 -
Revision I
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
W25Q32DWZEIG
IC FLASH SPI 32MBIT 8WSON
W25Q40BWSSIG
IC FLASH SPI 4MBIT 8SOIC
W25Q40BWZPIG
IC FLASH SPI 4MBIT 8WSON
W25Q64BVSFIG
IC SPI FLASH 64MBIT 16SOIC
W25Q64CVZEIG
IC SPI FLASH 64MBIT 8WSON
W25Q64DWZEIG
IC FLASH SPI 64MBIT 8WSON
W25Q64FVSFIG
IC SPI FLASH 64MBIT 16SOIC
W25Q80BVSNIG
IC SPI FLASH 8MBIT 8SOIC
相关代理商/技术参数
W25Q32BVZPIP
制造商:WINBOND 制造商全称:Winbond 功能描述:3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q32DW
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 32M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q32DWSFIG
功能描述:IC FLASH SPI 32MBIT 16SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q32DWSFIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 32M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q32DWSSIG
功能描述:IC FLASH SPI 32MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q32DWSSIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 32M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q32DWZEIG
功能描述:IC FLASH SPI 32MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP（0.465"，11.8mm 宽） 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8
W25Q32DWZEIG TR
制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8WSON